[13:58:04.783] CH58x_BLE_LIB_V1.90

[13:58:04.783] MESH_LIB_V1.73

[13:58:04.783] APP_DBG blemesh_on_sync> Bluetooth initialized

[13:58:05.264] APP_DBG prov_complete>

[13:58:05.279] APP_DBG blemesh_on_sync> Mesh network restored from flash

[13:58:05.300] APP_DBG blemesh_on_sync> Mesh initialized

[13:58:05.300] Initialized..

[13:58:05.300] Advertising..

[13:58:05.300]

[14:00:33.120] APP_DBG unprov_recv>

[14:00:33.120] APP_DBG link_open>

[14:00:33.343]

[14:00:36.780] APP_DBG node_added>

[14:00:36.780]

[14:00:39.273] APP_DBG link_close> reason 0

[14:00:39.273]

[14:00:40.215] APP_DBG cfg_cli_rsp_handler>

[14:00:40.215] APP_DBG cfg_cli_rsp_handler> Opcode 0x0000, timeout

[14:00:40.215] APP_DBG App_ProcessEvent> app_nodes[1] ADDR 2

[14:00:40.311]

[14:00:42.845] APP_DBG cfg_cli_rsp_handler>

[14:00:42.845] APP_DBG cfg_cli_rsp_handler> Opcode 0x0000, timeout

[14:00:42.845]

[14:00:44.316] APP_DBG App_ProcessEvent> app_nodes[1] ADDR 2

[14:00:44.316]

[14:00:45.473] APP_DBG cfg_cli_rsp_handler>

[14:00:45.473] APP_DBG cfg_cli_rsp_handler> Opcode 0x0000, timeout

[14:00:45.473]

[14:00:48.103] APP_DBG cfg_cli_rsp_handler>

[14:00:48.103] APP_DBG cfg_cli_rsp_handler> Opcode 0x0000, timeout

[14:00:48.103] APP_DBG App_ProcessEvent> app_nodes[1] ADDR 2

[14:00:48.327]

[14:00:50.733] APP_DBG cfg_cli_rsp_handler>

[14:00:50.733] APP_DBG cfg_cli_rsp_handler> Opcode 0x0000, timeout

[14:00:50.733]

[14:00:51.371] APP_DBG node_work_handler> Ran Out of Retransmit

[14:00:51.371] APP_DBG node_work_handler> Delete node complete

[14:00:51.371]

[14:13:01.001] APP_DBG node_added>

[14:13:01.001]

[14:13:03.607] APP_DBG link_close> reason 0

是不是不同公司的產品不能通用？

您好，中心節點例程是支持標準mesh的，由于標準mesh的吞吐量小，我們代碼里默認負載包長為221字節，注意修改以下參數為7；另外注意，中心節點例程里缺少通用模型比如通用開關模型的客戶端代碼，適配其他MCU的標準模型需要再添加。

好的， 再問一下，那個例程中有通用開關模型的客戶端的發送的代碼，我需要參考一下，多謝了