linux上面當大量接收數據的時候會出現丟數據，怎么處理？

驅動用https://github.com/WCHSoftGroup/ch9434ser_linux?最新的。

<3>[? 288.909323] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 294.113124] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 299.326623] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 303.476774] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 318.067465] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 323.432366] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 339.077988] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 344.254277] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 370.523683] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 375.450513] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 378.987159] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 384.117943] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 388.094397] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 393.530393] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 398.886174] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 400.481623] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 414.066184] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 418.073931] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 423.110287] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 428.857534] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 430.532406] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

<3>[? 433.044194] ch943x_spi spi1.0: Rx Overrun portno = 3, lsr = 0x63

您好。LSR=63表示接收緩沖區溢出了，您目前串口波特率是多少，建議調整到115200，同時可以提高SPI頻率到2M試下，

RTK應用深度使用。?

串口1串口3 是460800.

串口0是115200?

三個串口都有大量數據。

目前spi配的是10M

有什么好的辦法嗎？

我把fifo buf改小，及時去拿數據？

但改小又導致接收中斷頻繁吧，這樣又會影響數據發送？

目前l(fā)inux下最大帶寬話，就四個串口115200跑滿，由于Linux系統調度和SPI實際的延時，最大時鐘頻率的一般我們建議固定在2M，不太清楚您那邊需要多大的帶寬，后續有問題可以直接聯系郵箱

xcc@wch.cn